Full Length Mirror

DIY Full Length Mirror Tutorial Rogue Engineer 2
DIY Full Length Mirror Tutorial Rogue Engineer 3

Time to Complete

1 day

Estimated Cost

50 100

Skill Level

Beginner

In my attempt to keep up my good husband status I decided to build my wife the full length mirror that she has been requesting for some time. Luckily, I found a tall frameless mirror at Home Depot for about $35, and with a plywood backing and a couple 1x3s I was able to turn it into something awesome!

If you love this stuff as much as we do, you might want to consider following us on Instagram where we post sneak peeks and behind the scenes stuff in our stories. Also, did you know you can get tons of projects plans from all around the web when you follow us on Facebook and Pinterest!

Disclosure: This project was sponsored by Kreg Tool Company and DAP Products however the design and opinions are 100% my own.  

Disclosure: The links provided in the “materials” and “required tools” sections are affiliate links. If you would like to support our site and help keep our content free come find out more about how we can make money with no extra cost to you.

Step 1: Measure and Cut Plywood Backing

The mirror is not strong enough to support itself so we need to have a 3/4″ plywood backing. Measure the mirror so you have the exact size or just lay the mirror on the plywood and trace it.

DIY Full Length Mirror Plans Rogue Engineer 1

Then cut the plywood to the same size as the mirror. This can be done with a circular saw or a table saw. However, now that I have the Kreg Track Saw I don’t think I’ll ever break down a full sheet of plywood at the table saw again.

DIY Full Length Mirror Plans Rogue Engineer 2

Step 2: Cut Boards for the Frame

The top and the bottom 1×3 boards should be exactly the same width as the plywood and mirror. The side 1×3 boards should be the length of the mirror/plywood plus the thickness of the top and bottom boards combined. So if the mirror is 68″ tall and the top and bottom boards are 3/4″ thick then the side boards should be 69-1/2″.

DIY Full Length Mirror Plans Rogue Engineer 3

Step 3: Drilling the Pocket Holes

Set your pocket hole jig (I used the Kreg K5 Jig) to a thickness setting of 3/4″ and the stop collar to a screw depth of 1-1/4″. Then, drill pocket holes in the ends of each of the top and bottom boards.

DIY Full Length Mirror Plans Rogue Engineer 6

These pocket holes will get hidden by orienting them up on the top board and down on the bottom.

DIY Full Length Mirror Plans Rogue Engineer 7

Now drill pocket holes all the way around the plywood. Make sure there is one about 2-3″ from the corners and space the rest 10-15″ apart. The spacing doesn’t have to be exact.

DIY Full Length Mirror Plans Rogue Engineer 8

Step 4: Prepping for the Brass Rod

I decided to add a brass rod that could be used with s-hooks to hang smaller things like necklaces and such. If you would like to add the brass rod like we did then it is a good idea to drill those holes now. These holes are not through holes so we used a piece of tape on the bit to make sure they were drilled only about 1/4″ deep. Since our brass rod was 1/4″ we used the same size bit for a tight fit.

The location is up to you but we drilled 4″ down from the top of the sides and 3/4″ back from, what will be, the front inside face. Be sure to take note of the inside faces as the hole locations will be mirror on each side, not identical.

DIY Full Length Mirror Plans Rogue Engineer 10

Then, the brass rod gets cut down to the appropriate length. The length should be the width of the mirror plus the depth of both holes. So if the mirror is 16″ and the holes are 1/4″ deep then the brass rod should be cut to 16-1/2″ long. This can be done with a hacksaw.

Cutting Brass

Step 5: Applying a Finish

This is where you can get creative. We chose to go with a simple danish oil finish with a medium walnut tint to it and we love how it turned out. It is a quick and easy finish to apply.

DIY Full Length Mirror Plans Rogue Engineer 11

Step 6: Assemble the Frame

Now it is time to attach the 1×3 boards to the plywood. This is done with 1-1/4″ pocket hole screws through the, already drilled pocket holes and into the outer boards. Start with the top board as each end should line up with the sides of the plywood. The back edge of the 1×3 board should be flush with the back of the plywood and the pocket holes on the 1×3 should be facing outward.

DIY Full Length Mirror Plans Rogue Engineer 12

Then move around to the side and connect it to the top/bottom with 1-1/4″ pocket screws through the pocket holes drilled in the shorter 1×3 ends. Repeat the process until all of the pocket holes have been utilized.

Note: The brass rod may need to be inserted during this process.

DIY Full Length Mirror Plans Rogue Engineer 13

Step 7: Installing the Mirror

To install the mirror you’ll need a good adhesive. A great option is DAP’s DynaGrip Mirror, Marble and Granite Adhesive. The reason there is a specific adhesive for mirrors is because it will adhere to a non-porous. Unlike wood or concrete, a mirror, marble or granite are completely smooth creating a problem for most adhesives. And if you are ever adhering a mirror to a wall, DynaGrip will give you a permanent vertical hold in 1 hour.

DAP DynaGrip Mirror

Start by laying a bead all the way around the perimeter and then apply a serpentine to the center of the plywood.

DIY Full Length Mirror Plans Rogue Engineer 14

Carefully place the mirror into the frame. If you installed the brass rod you will have to slide it under that. Make sure not to force the mirror to hard into place. If it is a tight fit, try flexing the 1×3 to allow the mirror to fully rest on the plywood. If you are still having trouble then you can try removing the screws that connect the top/bottom to the sides and try to flex the 1×3 that it is hitting again.

DIY Full Length Mirror Plans Rogue Engineer 15

Once the mirror is fully seated against the plywood backing, allow the adhesive to cure for 1 hour until standing upright.

Finished

With the adhesive fully cured you can now stand the mirror upright and into place. We decided to lean our mirror against the wall which works out really well. If you would like to hang the mirror you might want to screwing keyhole hangers into the back like we did on this display ledge. If you were to install the hanger on the back of the 1×3 frame you could pre-drill and use longer screws for a stronger connection.

DIY Full Length Mirror Tutorial Rogue Engineer 2

I hope you enjoyed this project. It was a pretty easy one and will get daily use I’m sure!

About The Author

Related Posts