Build a Julius Wine Table

An Easy to Build Table with Wine Storage

There can never be enough wine storage, right? Ok, I may be the exception because I have a “thing” for wine… If you do, too, then the plans to build a Julius wine table are for you! With three shelves to hold six bottles each and a drawer for supplies, you will definitely be ready for your next shindig – or to just display your fine collection!

free plans to build a joss main inspired julius wine table_Copy

Materials:

Lumber:

  • 2 – 2×2 at 6′
  • 1 – 1×2 at 8′
  • 4 – 1×3 at 8′
  • 1 – 1×6 at 4′
  • 1 – 4′ x 4′ sheet of 3/4″ plywood

Cut List:

  • 4 – 2×2 at 31-1/4″ – Legs
  • 2 – 3/4″ plywood at 7-3/4″ x 8-3/4″ – Side Panels
  • 1 – 3/4″ plywood at 7-3/4″ x 24-3/4″ – Back
  • 2 – 1×2 at 24-3/4″ – Front Stretchers
  • 2 – 1×3 at 4-3/4″ – Fronts
  • 4 – 1×2 at 10-1/4″ – Drawer Supports
  • 3 – 1×3 at 24-3/4″ – Bottle Shelf Backs
  • 2 – 1×6 (ripped to 5″ wide) at 24-3/4″ – Bottle Shelf Fronts
  • 21 – 1×3 at 10-1/4″ – Bottle Shelf Slats
  • 1 – 3/4″ plywood at 12-3/4″ x 28-3/4″ – Top
  • 1 – 3/4″ plywood at 9-1/4″ x 17-1/4″ – Drawer Bottom
  • 2 – 3/4″ plywood at 4-1/2″ x 9-1/4″ – Drawer Sides
  • 1 – 3/4″ plywood at 4-1/2″ x 18-3/4″ – Drawer Back
  • 1 – 3/4″ plywood at 5-3/4″ x 20-3/4″ – Drawer Front

free plans to build a joss main inspired julius wine table

Click on the drawings for a larger view!

Step One

Cut the pieces for the legs and side panels. Drill pocket holes in each end of the panels as well as one long edge (to attach the top). Secure the panels to the legs using glue and 1-1/4″ pocket hole screws. The outside face of the panels will be flush with the outside face of the legs.

free plans to build a joss main inspired julius wine table_Sides

Step Two

Cut the piece for the back panel. Drill pocket holes in each end of the panel as well as one long edge (to attach the top). Secure the panel to the legs using glue and 1-1/4″ pocket hole screws. The outside face of the panel will be flush with the outside face of the legs.

free plans to build a joss main inspired julius wine table_Back

Step Three

Cut the pieces for the fronts and the front stretchers. Drill pocket holes in each end of each piece. Attach the stretchers to the legs as shown using glue and 1-1/4″ pocket hole screws.

Attach the fronts to the stretchers using glue and 1-1/4″ pocket hole screws.

free plans to build a joss main inspired julius wine table_Front Stretchers

>free plans to build a joss main inspired julius wine table_Fronts

Step Four

Cut the pieces for the drawer supports and drill pocket holes in each end. These supports will keep the drawer in place since there will be no drawer slides. Attach to the cabinet using glue and 1-1/4″ pocket hole screws.

free plans to build a joss main inspired julius wine table_Drawer Supports

Step Five

Cut the pieces for the bottle shelf backs and drill pocket holes in each end. Secure to the legs as shown using glue and 1-1/4″ pocket hole screws.

free plans to build a joss main inspired julius wine table_Bottle Shelf Backs

Step Six

Cut the pieces for the bottle shelf fronts. It will be easier to cut the holes with a hole saw, then rip the piece in half. The holes are set at 3-5/8″ on center and are 2″ in diameter. Once the pieces are cut apart (there will be one extra), drill pocket holes in each end.

free plans to build a joss main inspired julius wine table_Bottle Shelf Fronts 1

free plans to build a joss main inspired julius wine table_Bottle Shelf Fronts 2

Step Seven

Cut the pieces for the bottle shelf slats and drill pocket holes in each end. There will be 1-1/8″ spacing between the slats. The center of the spacing will be at the center of the half circles which will help hold the bottles in place so they don’t roll around. Secure the slats using glue and 1-1/4″ pocket hole screws.

free plans to build a joss main inspired julius wine table_Slats

Step Eight

Cut the piece for the top. The top will overlap by 1/2″ on each side and 3/4″ at the front. Secure in place using glue and 1-1/4″ pocket holes.

free plans to build a joss main inspired julius wine table_Top

Step Nine

Cut the pieces for the drawers. Drill pocket holes in each end of the sides as well as all four edges of the bottom. Assemble as shown using glue and 1-1/4″ pocket hole screws. The front will overlap the drawer box by 1″ at each side, 3/4″ at the top, and 1/2″ at the bottom. Before inserting the drawer in the cabinet, coat the bottom with paste wax which will allow the drawer to slide smoothly.

free plans to build a joss main inspired julius wine table_Drawer BSfree plans to build a joss main inspired julius wine table_Drawer FBfree plans to build a joss main inspired julius wine table_Drawer Front

Finish as desired.

The free plans to build a Joss & Main inspired Julius Wine Table are an easy build that will look as if you spent tons of time on it! Beautiful, right? Got a project you’ve completed using my plans? Share photos with me at cher {at} designsbystudioc {dot} com or designsbystudioc {at} gmail {dot} com. I would love to feature your work on DbSC!

Originally posted 2013-05-02 08:00:39.