How to Build a Detached Deck

Transform a boring backyard with these step-by-step instructions.

Decks are a great way to add defined space to an otherwise-empty yard — and you can entertain in high style. Here’s the building plan:

Materials and Tools:

Finished detached deck with coral and neutral furniture.

Deck After

After

After

contractor’s marking paint
8 precast concrete piers
2x6-inch boards
4x6-inch boards
4-inch composite planks for decking
12-inch planks for deck facing
shims
1-3/8-inch joist hanger nails
joist hangers
3-inch galvanized framing nails
2½-inch composite deck screws
prefabricated stair risers
miter saw
drill
tamper
chalk line
level
chain saw
hammer
deck guide

Steps:

1. Measure and mark the outline of your deck. Measure and mark where your concrete piers will sit. When laying each pier, make sure they’re no more that 6 feet apart. (Check local building codes; they may require that you use more than just piers.)

2. If you have a grass yard, cut out the sod so that the pier will sit easily on solid ground. Wherever you’ll be placing a pier, use a tamper to compact the ground. This will make sure that the earth is solid enough to support the weight of the deck.

3. Once the piers are placed, lay the girders in the joist hangers on the concrete piers. Set each end of a level on a separate girder to make sure they’re both the same level. If they aren’t, tamp down the soil of the higher pier until it’s level. If you can’t lower the pier, place shims under the girder to raise it to the appropriate level. Make sure all the joists are even by placing the level between each joist. Nail the joists into place.

4. Lay the cross beams out 16 inches from center over the girders. Since the pictured deck has an angled side, the first four beams are 136 inches long, the fifth beam is 127½ inches, the sixth is 111½ inches, the seventh is 95½ inches, the eighth is 79½ inches and the last beam is 63½ inches. Attach the cross beams to the 4-by-6 beams with joists hangers.

Man measuring wood for deck.

Detached Deck Building Process

Place 2x4’s along the ends of the cross beams on each side of the deck and secure with framing nails. Add joist hangers where the frame and the cross joist intersect. Because the deck will have an angled side, miter the ends of the two frame beams that will sit on either side of the angle to 45 degrees. Place the beam that runs along the angled side, and attach with the framing nails.

Place 2x4’s along the ends of the cross beams on each side of the deck and secure with framing nails. Add joist hangers where the frame and the cross joist intersect. Because the deck will have an angled side, miter the ends of the two frame beams that will sit on either side of the angle to 45 degrees. Place the beam that runs along the angled side, and attach with the framing nails.

5. Place 2x4’s along the ends of the cross beams on each side of the deck and secure with framing nails. Add joist hangers where the frame and the cross joist intersect. Because the deck will have an angled side, miter the ends of the two frame beams that will sit on either side of the angle to 45 degrees. Place the beam that runs along the angled side, and attach with the framing nails.

6. With a chain saw, cut the end of the girders that extend past the edge of the frame. Start from the back of the deck and work your way to the front. Place your first beam 1½ inches over the frame. It’s usually recommended that you don’t leave more than an inch of overlay, but we’ll be adding a ½-inch facing to the side of the deck.

Man using a deck guide to align holes for drilling.

Deck Guide

Use a deck guide when placing your decking. This will assure that each piece is uniformly spaced. For the pictured project, the pieces are spaced ¼-inch apart. The deck guide will also allow you to align the spaces for pre-drilling holes. With 2½-inch deck screws, attach the beams to the frame. As you near the end, you can adjust the deck spacing so you end up with a 1½-inch overhang on the opposite side.

Use a deck guide when placing your decking. This will assure that each piece is uniformly spaced. For the pictured project, the pieces are spaced ¼-inch apart. The deck guide will also allow you to align the spaces for pre-drilling holes. With 2½-inch deck screws, attach the beams to the frame. As you near the end, you can adjust the deck spacing so you end up with a 1½-inch overhang on the opposite side.

7. Use a deck guide when placing your decking. This will assure that each piece is uniformly spaced. For the pictured project, the pieces are spaced ¼-inch apart. The deck guide will also allow you to align the spaces for pre-drilling holes. With 2½-inch deck screws, attach the beams to the frame. As you near the end, you can adjust the deck spacing so you end up with a 1½-inch overhang on the opposite side.

8. Once your decking is placed, snap a chalk line across the outside ends of the boards. Trim along the chalk line with a circular saw, making the jagged side of the deck straight.

9. For the stairs, use prefabricated risers. Cut a section big enough for the cross beam to fit, starting at the base of the third step. If the riser is too big, trim the bottom. Make sure all the risers sit completely level. Once in place, drill 4-inch screws through the cross beam and into the portion of the riser behind it. For extra strength, add front and back 2x4’s for each level of stairs. Attach the rear 2x4’s of the second step to the frame. Add the decking material to the stairs.

10. Cut your 12-inch deck facing to size (if needed) for each side of the deck. Miter the ends of each piece so they form clean corners. Place the facing on the outer side of the frame so it skirts around the deck. Attach it with 3-inch galvanized framing nails.

Next Up

How to Build a Backyard Deck

Host Steve Watson helps a homeowner build a backyard deck.

Adding Lattice to the Bottom of a Deck

Turn the open space underneath your deck into closed storage by creating a lattice wall with a gate.

Make a Planter Box With Nail Head Trim

Create stylish planters, complete with bolt head trim, to flank and define your front door.

How to Stain a Wooden Deck

Enhance and protect your outdoor design by learning how to stain a deck with these simple steps using deck stain.

How to Build a Floating Shelf With Hidden Charging Station

Don't let unsightly cables and cords clutter your living space. This DIY floating shelf has a built-in power strip tucked away in a drawer — the perfect spot to charge your phones, tablets and other gadgets out of sight.

How to Build a Grilling Island

Create an outdoor kitchen by nestling a gas grill into a custom-built, granite-topped island.

How to Build a Covered Sandbox

This weekend, build a covered sandbox for the kids. The roof on this DIY sandbox will keep the play area well-shaded and free of leaves, twigs and rain.

How to Determine Your Deck Style

Learn what factors and styles to consider when planning your deck.

Decks for Every Location

Learn about the best options for deck locations

How to Properly Paint Your Home's Exterior

Give your house a fresh, updated look with exterior paint.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.